浏览正文,请点击 → 【关闭】
设为首页 | 加入收藏 | 联系我们
STANDARD123.COM -- 全球标准&认证知识个人分享网站

推荐阅读:全球标准认证知识导图 (15年行业经验总结)
提供全球各国证书有效性查询
--包括UL,VDE,TUV,SAA,CSA,SGS,CB,ETL,BSI等证书查询及各国法规查询网址列表!
| 首页 | 欧洲认证 | 亚洲认证 | 北美洲认证 | 南美洲认证 | 大洋州认证 | 非洲认证 | 国际认证 | 认证专题 | 认证代理 | 标准阅览
当前位置:首页 >> 全球标准认证 >> 认证专题 >> 标准测试方法 >> 正文


Needle -flame Test




来源: 点击数:10  录入时间:07-05-30 12:02:02

1.       Test goal

 

To assess the fire hazard which be produced by small flames

 

2.       Application

 

Up to the end product standards

 

3.       Test apparatus

 

a. In vertical position, height of test flame is 12 + 1 mm

 

b. A piece of flat smooth white pinewood board, 10 mm thick covered by a single layer of wrapping tissue, is positioned at a distance of 200 + 5 mm below the place where the needle flame is applied to the specimen.

 

c. for free-standing equipment, it is placed in its normal position of use on the tissue-covered board extending for 100 mm outside the base of the appliance in all directions.

 

d. For wall-mounted equipment, it is fixed in its normal position of use 200 + 5 mm above the tissue covered board.

 

4.       Conditioning

 

The board and tissue are stored for 24h at 15 ~ 35 o C & 45 ~ 75%RH.

 

5. Test specimens

 

a. If the test can not be made on the complete specimen, a suitable part may be cut from it.

 

b. Care must be taken to ensure that the test flame is not applied incorrectly, for example to an edge created by cutting.

 

6. Test procedure

 

a. The specimen is arranged in its most unfavorable position of normal use.

 

b. During the adjustment of the test flame, any influence of heat or radiation on the specimen shall be avoided.

 

c. The test flame is applied to that part which is likely to be affected by flames resulting from normal use or from fault conditions, or from any source of ignition accidentally applied.

 

d. The burner must stop when the tip of flame is in contact with the specimen.

 

e. The test flame is removed after t a - 5/10/20/30/60/120 (+0, -1) s.

 

f. For EN60598-1, t a is 10 s.

 

g. Unless other specified, the test is made on three specimens.

 

7. Evaluation

 

Pass the test if one of the following situation applies:

 

a. No flame and no glowing of the specimen and no ignition of the wrapping tissue or

scorching of the pinewood board.

 

b. Flames or glowing extinguish within 30s after the removal of the needle-flame – t b < 30s, the surrounding parts and the layer below have not burnt away completely and there has been no ignition of the wrapping tissue nor scorching of the pinewood board.

 

Note: t b is the duration of burning.

t a is the duration of application of the test flame.
Appendix A Illustration of Test flame (See figure 1)




享受分享的乐趣↓

 

   
  ·上一篇文章:Impact Test---IEC
  ·下一篇文章:包装运输测试(ISTA 3A)
 
相关文章: 图片资讯:
>> 滚动更新
最近更新
热门文章
推荐文章
友情链接:[国际标准化组织(ISO)] [国际电工委员会(IEC)] [欧洲电工标准化委员会(CENELEC)] [欧洲标准化委员会(CEN)] [国家质量监督检验检疫总局(AQSIQ)]
          [国家认证认可监督管理委员会(CNCA)] [中国合格评定国家认可委员会(CNAS)] [中国质量认证中心(CQC)]
Copyright 2006-2021 Standard123.com Inc. All rights reserved. 版权所有 粤ICP备06119707号
联系方式:HDUU@MSN.COM(MSN) 电子邮箱: Webmaster@standard123.com